Lost Vape Paranormal DNA 250C Instructions-User Manual

Lost Vape paranormal DNA 250C Introduction

The paranormal DNA 250C is the highly advanced edition of the Paranormal series, boosting in power with the integration of Evolv’s latest DNA 250c Color Chipset while maintaining the beloved chassis design and luxury materials.

The Paranormal DNA 250C utilizes Evolv’s most advanced DNA 250C board with down-throttled power, featuring an incredible 98% output efficiency rating, tremendous range from 1 to 200 watts, new puff replay feature to maintain preferred puffs, and couple with USB-The-Go feature for power sharing.

Continuing the legacy of developing luxurious and elegant design, the Paranormal DNA 250c is machined out of die-cast Zinc Alloy with stainless steel faceplate and buttons, genuine leaher battery door and customized side panels. The paranormal DNA 250C is able to reach 200watts with the implementation of dual 18650 batteries.

In order to satisfy and spare vaper’s needs and time, Lost Vape Paranormal DNA 250c provides preset profiles in Nikel (Ni200), Titanium(Ti) and Stainless Steel (SS) coil builds for ready to go.

Paranormal DNA 250C Standard Package

1 x Paranormal DNA 250C Device
1 x Paranormal Use Manual
1 x Customized Side Panels
1 x USB Connecting Cable
1 x USB On-The-Go Adaptor

This panel remover is used to take off the wood/carbon fiber panels.
Firstly, press the remover to the panel until it holds tight.
Secondly, pull it backward to take the panel out.

Note: Certain customized edition panels (Resin or Stab Wood etc.) are pre-installed which are not removable.

paranormal DNA 250C Mod Main Features

Power by Evolv Firmware Upgradable DNA 250C board
Dual 18650 Cells Setup for Long-lasting Power
Theme Designer Software/Customizable User Interface
Temperature Limit: 200℉-600℉
Output Power: 1watt – 200watts
Puff Replay
USB On-The-Go Charger
Body Material: Die Cast Zinc Alloy
Gun Metal and Stainless Steel Finishes
Electroplating Paintwork Firms Appearance
Included Customized Panels
Customized Leather Panel Wraps With Foam Cushion
Flip-Open Bottom Battery Sled for Battery Replacement
Spring Loaded Nickel Plated Brass Center Pin
Integrated 2A Onboard Charger
Dimensions: 91.5mm*55mm*27.5mm

 Evolv DNA 250C

The DNA 250C is a power regulated digital switch mode DC-DC converter for personal vaporizer. It features Evolv’s patented wattage control, Temperature Protection, Puff Replay, Preheat, full color TFT screen, On-The-Go USB, Reverse Polarity Protection, and onboard buttons, and a real-time clock. Evolv’s Escribe software and Theme Designer software can be used to fully customize all aspects of the interface and monitor the user experience. The DNA 250C runs on two lithium ion batteries, and features battery monitoring and an integrated 2A charger.


DNA 250C Mod Operating Range

Specifications

Absolute Limits

Output Power

The following graphs show the output power range of the DNA 250C as a function of the coil resistance.

Escribe

Escribe is a software package used to configure, monitor and modify the operation if your DNA 250C. It installs on a Windows PC and connects to your DNA 250C using the USB port. Escribe has a separate manual and tutorial which can be found on Evolv’s site.


http://www.evolvapor.com/
http://www.evolvapor.com/manuals/EScribeManual.pdf

Display of DNA 250C

To wake the device from power off state, tap the Fire button. To generate vapor, press the fire button. To change the wattage setting for more less vapor, click or hold the UP and Down buttons.

DNA 250C Vape Mod Error Messages

The DNA 250C will indicate a variety of error states.

Check Atomizer: The DNA does not detect an atomizer, the atomizer has shorted out, or the atomizer resistance is incorrect for the power setting.

Weak Battery: The battery is deeply discharged and needs to be charged, or is damaged. If this happens, the DNA 250C will not fire the atomizer. The Check Battery message will continue to display for a few seconds after attempting to fire the device. User should remove and replace the battery.

Shorted: The atomizer or writing are short circuited.

Ohms Too Low: The resistance of the atomizer coil is too low for the current wattage setting. If this happens, the DNA 250C will continue to fire, but will not be able to provide the desired wattage. The ohms too low message will continue to display for a few seconds after the end of puff.

Ohms Too High: The resistance of the atomizer coil is too high for the current wattage setting. If this happens, the DNA 250C will continue to fire, but will not able to provide the desired wattage. The ohms Too High message will continue to display for a few seconds after the end of puff.

Temperature Protection: The heating coil reaches the maximum allowed temperature during the puff. If this happens, the DNA 250C will continue to fire, but will able to provide the desired wattage.

Weak Battery: The battery needs to be charged, or higher amp rated battery needs to be used. If this happens, the DNA 250C will continue to fire the atomizer, but will not be able to provide the desired wattage. The Weak Battery massage will continue to display for a few seconds after the end of the puff.

Return To researched: The DNA has reached a limit configured by a researcher.

Too Hot: The DNA 250C has onboard temperature sensing. It will shut down and display this message if the internal board temperature becomes excessive.

Lost Vape Paranormal DNA Puff Replay

Puff replay is a new feature on the DNA 250C that allows the user to save and play back puffs. The use of a temperature sensitive material is required such as Nickel, Stainless Steel, Titanium, or other material that increases in resistance when heated. Puff Replay works in either temperature protection or wattage control modes and will also prevent dry hits when used with wattage control.

To use Puff Replay set the device to desired power level and operate it normally. Once a satisfying puff is achieved, activate Puff Replay to replay the last puff on all subsequent uses. Puff length is not a factor and the user will not be limited to the length of the previous puff. Disable Puff Replay to resume normal operation or find a new puff to save. If Puff Replay cannot be enabled the coil is not compatible.

Paranormal DNA 250C Mod Charging and USB On-The-Go

Charging the batteries
Internal Charging: The DNA 250C has a built-in 2A USB charger. It automatically detects the type of USB power supply it is connected to, so it can be plugged into the standard PC USB ports or higher power charger. The max charge current is based on the cell capacity as programmed in EScribe.

External charging (Recommend): Remove the batteries from device.
Follow charging instructions with using charger.

USB On-The-Go
The DNA 250C supports USB On-The-Go. An OTG adapter may be plugged into the Micro USB port on the device to charge any other device capable of charging via USB. Charging starts and stops automatically and OTG charging will not over-drain the DNA 250C